AN 822: Intel® FPGA Configuration Device Migration Guideline

Download PDF
ID 683340
Date 4/29/2020
Public
Document Table of Contents
Document Table of Contents x
1. Intel® FPGA Configuration Device Migration Guideline
1. Intel® FPGA Configuration Device Migration Guideline x
1.1. Migration Considerations 1.2. Software Migration Guidelines 1.3. Specification Comparison 1.4. Evaluating Data Setup and Hold Timing Slack 1.5. Migration Method from EPCQ to EPCQ-A for Arria® V, Cyclone® V, and Stratix® V Devices 1.6. Cyclone® V to Cyclone® V QS Device Migration Reference Manual 1.7. Document Revision History for AN 822: Intel® FPGA Configuration Device Migration Guideline
1.2. Software Migration Guidelines x
1.2.1. IP Core Compatibility 1.2.2. Programming File Compatibility 1.2.3. IP Core and Programming File Migration Guideline 1.2.4. Software Support for EPCQ-A Devices
1.2.3. IP Core and Programming File Migration Guideline x
1.2.3.1. IP Core Regeneration Guideline 1.2.3.2. Programming File Regeneration Guideline
1.3. Specification Comparison x
1.3.1. Operating Conditions 1.3.2. Timing Specifications 1.3.3. Operation Codes 1.3.4. Pin Information 1.3.5. Package Dimensions 1.3.6. Status Register
1.3.2. Timing Specifications x
1.3.2.1. Read Operation Timing 1.3.2.2. Write Operation Timing
1.3.4. Pin Information x
1.3.4.1. 8-pin SOIC Device Pin Information 1.3.4.2. 16-pin SOIC Device Pin Information
1.3.5. Package Dimensions x
1.3.5.1. 8-Pin SOIC Device Package Dimensions 1.3.5.2. 16-Pin SOIC Device Package Dimensions
1.3.6. Status Register x
1.3.6.1. Sector Protect
1.5. Migration Method from EPCQ to EPCQ-A for Arria® V, Cyclone® V, and Stratix® V Devices x
1.5.1. Board Design Guidelines for the Active Serial (AS) Configuration Scheme
1.5.1. Board Design Guidelines for the Active Serial (AS) Configuration Scheme x
1.5.1.1. IBIS Simulation Example 1.5.1.2. Example for Adding the RC Network on DCLK 1.5.1.3. Example for Adding Buffer on the DCLK 1.5.1.4. Simulating the DCLK Signal at 100 MHz Operation 1.5.1.5. Trace Propagation Delay Recommendation For DCLK Running at a 100-MHz Operation
1.5.1.2. Example for Adding the RC Network on DCLK x
1.5.1.2.1. Example for Simulating the DCLK Link 1.5.1.2.2. Example for Simulating the DATA Link 1.5.1.2.3. Simulation Results
1.5.1.3. Example for Adding Buffer on the DCLK x
1.5.1.3.1. Simulation Results
1. Intel® FPGA Configuration Device Migration Guideline

1.2.3. IP Core and Programming File Migration Guideline

Note: This section describes programming file compatibility for designs with Intel® FPGA IP cores that interface with the configuration device.

Refer to the following diagram to determine the subsequent tasks and guidelines for migration:

  • IP core and programming file are incompatible—regenerate IP core and programming file shown in IP Core Regeneration Guideline.
  • Programming file is incompatible—regenerate programming file shown in Programming File Regeneration Guideline.
  • IP core and programming file are compatible—no additional task required and you can reuse the existing programming file.
Figure 2. IP Core and Programming File Compatibility Flow Chart

Section Content
IP Core Regeneration Guideline
Programming File Regeneration Guideline

Level Two Title