PCB Stackup Design Considerations for Intel® FPGAs

Download PDF
ID 683883
Date 6/28/2017
Public
Document Table of Contents
Document Table of Contents x
1. PCB Stackup Design Considerations for Intel® FPGAs
1. PCB Stackup Design Considerations for Intel® FPGAs x
1.1. PCB Stackup Construction 1.2. Material Selection 1.3. Glass Transition Temperature 1.4. PCB Stackup Design 1.5. PCB Panelization 1.6. Conclusion 1.7. Specific Recommendations for Intel® FPGA Devices 1.8. References 1.9. Document Revision History
1.2. Material Selection x
1.2.1. Material Loss Considerations
1.2.1. Material Loss Considerations x
1.2.1.1. Relative Dielectric Constant 1.2.1.2. Loss Tangent 1.2.1.3. Fiberglass Weave Composition 1.2.1.4. Skin Effect
1.4. PCB Stackup Design x
1.4.1. Layer Count 1.4.2. Signal Layers 1.4.3. High Speed Signal Layer Planning 1.4.4. Power and Ground Layers 1.4.5. Power Plane and Capacitor Placement Strategy 1.4.6. Planar Capacitance and Spreading Inductance 1.4.7. Plane Layer Separation 1.4.8. Copper Weight 1.4.9. Hybrid Construction
1.4.5. Power Plane and Capacitor Placement Strategy x
1.4.5.1. General Rules for Capacitor and Power Plane Placement 1.4.5.2. Rules for Transceiver Power Plane Placement 1.4.5.3. Rules for High-Current Power Rails 1.4.5.4. Rules for PLL and Other Power Rails
1.7. Specific Recommendations for Intel® FPGA Devices x
1.7.1. Stratix® 10 Device Recommendations 1.7.2. Stratix® V Device Recommendations 1.7.3. Stratix IV Device Recommendations 1.7.4. Arria® 10 Device Recommendations 1.7.5. Arria® V Device Recommendations 1.7.6. Arria II Device Recommendations 1.7.7. Cyclone® 10 Device Recommendations 1.7.8. Cyclone® V Device Recommendations 1.7.9. Cyclone® IV Device Recommendations 1.7.10. Cyclone III Device Recommendations
1.7.1. Stratix® 10 Device Recommendations x
1.7.1.1. Stratix® 10 Device Family Power Plane Placement Example
1.7.2. Stratix® V Device Recommendations x
1.7.2.1. Stratix® V GX, GT, and GS Family Power Plane Placement Example 1.7.2.2. Stratix® V E Family Power Plane Placement Example 1.7.2.3. Stratix® V Transceiver Channel Breakout Recommendations
1.7.3. Stratix IV Device Recommendations x
1.7.3.1. Stratix IV GX and GT Family Power Plane Placement Example 1.7.3.2. Stratix IV E Family Power Plane Placement Example
1.7.4. Arria® 10 Device Recommendations x
1.7.4.1. Arria® 10 Device Family Power Plane Placement Example
1.7.5. Arria® V Device Recommendations x
1.7.5.1. Arria® V Device Family Power Plane Placement Example
1.7.6. Arria II Device Recommendations x
1.7.6.1. Arria II GX Family Power Plane Placement Example
1.7.7. Cyclone® 10 Device Recommendations x
1.7.7.1. Cyclone® 10 LP Device Family Power Plane Placement Example
1.7.8. Cyclone® V Device Recommendations x
1.7.8.1. Cyclone® V Device Family Power Plane Placement Example
1.7.9. Cyclone® IV Device Recommendations x
1.7.9.1. Cyclone® IV GX Family Power Plane Placement Example 1.7.9.2. Cyclone® IV E Family Power Plane Placement Example
1.7.10. Cyclone III Device Recommendations x
1.7.10.1. Cyclone III Family Power Plane Placement Example
1. PCB Stackup Design Considerations for Intel® FPGAs

1.2. Material Selection

The complex FPGA boards that incorporate the Stratix® 10 device families of transceiver technologies require higher layer counts as well as lower loss materials to run at up to 56 Gbps. High layer count facilitates the high density signal break-out, routing, and power distribution, while the high-performance low-loss material is required to successfully transmit and receive 10 Gbps+ transceiver data rates over extended backplane channel lengths. High layer count PCBs often suffer from lamination and drilling challenges in the PCB manufacturing process. Together with low-loss materials, they put added cost pressure on the system designer. To meet these challenges, designers must understand the material properties that influence signal loss and PCB manufacturability in order to properly select the best performance material at the lowest cost for a successful and robust design.

Level Two Title